80mm Rear Wheel for Mini & Maxi

SKU: AC0021

• Product Details

  The long-lasting polyurethane wheel comes with the bearings and spacer already installed, making switching your wheels quick and easy. Order two if replacing both rear wheels. 80mm.

  To install:

  1. Use two 1/8 Allen keys. Insert one into the screw side (which is completely round) and one into the bolt side.
  2. Hold the bolt side still, and turn the Allen key in the screw side counter-clockwise until it loosens. If the blue lock-tight glue used in the original manufacture is still in place, you may need to use a little muscle to loosen the screw.
  3. Pop the wheel out, replace it with a new one, and reattach the screw.

• Video

Handlebar Grips for Mini & Maxi

SKU: 1358

• Product Details

  This set of two rubber handle bar grips make it easy to update the T-grip portion of your scooter.

  To install:

  1. Use scissors to remove stock grips and any remaining rubber fragments.
  2. Pour water into new grips, then pour it out. This step temporarily lubricates grips.
  3. Slide wet grips onto T-bar, butting grip edges against the shaft of the T-bar. (Proper positioning is very important to keep grips from sliding off.)
  4. Allow grips to dry before riding.

Brake for Mini

SKU: 1687

• Product Details

  This tiny part works hard to keep riders safe in stop-and-go traffic. Check yours for wear periodically and replace when necessary. To install: Use a Phillips-head screwdriver to unfasten the eight black screws on the underside of the scooter. Remove the colored deck from the black frame, lifting up from the rear of the scooter first. Unfasten the two silver screws next to the brake, then remove the bolts and stock brake. Replace with new brake, reattaching bolts. Position the deck on the black base, rear end first, and replace the eight screws.

120mm Clear Front Wheel for Mini & Sprite

SKU: AC5005B

• Product Details

  When pitted sidewalks and bumpy streets wear down wheels, it’s easy to replace them. Each wheel comes with bearings and spacer pre-installed. (Order two if replacing both front wheels.) 120mm.

   

  To install:

  1. Use two 1/8 Allen keys. Insert one into the screw side (which is completely round) and one into the bolt side.
  2. Hold the bolt side still, and turn the Allen key in the screw side counter-clockwise until it loosens. If the blue lock-tight glue used in the original manufacture is still in place, you may need to use a little muscle to loosen the screw.
  3. Pop the wheel out, replace it with a new one, and reattach the screw.

Mini Seat with O-Bar

• Product Details

  Turn any colored Mini or Mini Deluxe scooter into a Mini 3in1, and extend the life of your ride!

  Designed for use with a Mini scooter, the Seat & O-bar attachment transforms a Mini scooter into a stable ride-on with seat for young children, starting at age 1. Toddlers love sitting to scoot, and it helps young children gain confidence and comfort with their Micro. At age 2, the seat can be removed so that toddlers can stand on the deck using the shorter O-bar handle bar.

  Please note that a Micro Mini or Mini Deluxe scooter is required to use the Seat and O-bar attachment. If you don't already own a Micro for ages 2-5, you may either purchase the Micro Mini 3in1 Deluxe completely pre-packaged, or purchase a Micro Mini scooter separate from the Seat & O-bar attachment.

Bolt & Screw for Mini Rear Wheel & Shank

SKU: 1138

• Product Details

  Replacing the hardware on your rear wheel/front wheel is quick and easy. Comes complete with instructions. (Not compatible with Micro Maxi).

  To install:

  1. Using two Allen keys, insert one into the square side of the bolt and hold it steady. Insert the second Allen key into the round side of the bolt and rotate counterclockwise to loosen.
  2. Replace with new bolt and screw. Tighten down, holding the square side steady with one Allen key and rotating the other Allen key clockwise in the round side.

B-Bend Springs

SKU: 1227

• Product Details

  This set of two wire springs fit behind the two front wheels, helping your scooter maintain proper steering tension.

  To install:

  1. Look for the two screws on the bottom of the scooter, just behind the two front wheels. Remove the screws.
  2. Remove the rectangular black spacer.
  3. Use a flat head screwdriver to pry out the stock b-bend springs.
  4. Pull the wheels away from the b-bend, insert the spring into place, and press down with your thumb.
  5. Replace the black spacer and screws.

• Video

Deck for Mini

SKU: 1337

• Product Details

  A brand new deck makes your whole scooter look like new, especially when you combine it with matching handlebar covers (sold separately).

  To install:

  1. Use a Phillips-head screwdriver to remove the eight black screws on the underside of the scooter.
  2. Remove the colored deck from the black frame, lifting up from the rear end of the scooter first.
  3. Position the new deck on the black frame, snapping the rear end on first.
  4. Replace the eight screws.

• Video

Steering Link
Bolt/Screw/Washer for Mini & Maxi

SKU: 1344

• Product Details

  Steering Link (bolt/screw/washer) for Micro Mini / Maxi - Part #1147. This part attaches one side of the steering crossbar. Compatible with Micro Mini and Micro Maxi only

T-bar for Mini
Children

SKU: 1140

• Product Details

  T-bar for Micro Mini. Compatible with Micro Mini, Micro Mini 2-Go, Micro Mini 3in1, and Micro Mini Sporty

• Specs

  • Age Range :
    Children

Left Axle for Mini

SKU: 4662

• Product Details

ABEC Bearings

SKU: AC1007

• Product Details

  Pair of replacement ABEC precision Bearings for scooter wheel. Our polyurethane wheels require (2) bearings apiece. Spacer not included. Pricing: (2) Bearings = $3.99 with free shipping (4) Bearings = $5.99 with free shipping (6) Bearings = $7.99 with free shipping (additional bearing pairs = $2 after the first set is placed into shopping cart)

Right Axle for Mini

SKU: 4660

• Product Details

Left Side Washer

SKU: MMWL1146

• Product Details

  Minimize friction and optimize pressure between the wheel and the scooter bottom.

  To install:

  1. First, take off the old wheel. Using two Allen keys, insert one into the square side of the bolt and hold it steady. Insert the second Allen key into the round side of the bolt and rotate counterclockwise to loosen. Remove the wheel.
  2. Remove the screw holding the shank to the scooter.
  3. Remove the washer between the shank and scooter bottom.
  4. Place the new washer between the shank and scooter bottom.
  5. Replace the shank, securing it to the scooter chassis by tightening the screw.
  6. Slide the square side of the bolt into the shank so the round side of the bolt points to the outside of the scooter.
  7. Slide the wheel onto the bolt.
  8. Using two Allen keys, insert one into the square side of the bolt and hold it steady. Insert the second Allen key into the round side of the bolt and rotate clockwise to tighten.

Right Side Washer

SKU: MMWR1146

• Product Details

  Reduce friction and ensure even pressure between the wheel and the scooter bottom

  To install:

  1. First, take off the old wheel. Using two Allen keys, insert one into the square side of the bolt and hold it steady. Insert the second Allen key into the round side of the bolt and rotate counterclockwise to loosen. Remove the wheel.
  2. Remove the screw holding the shank to the scooter.
  3. Remove the washer between the shank and scooter bottom.
  4. Place the new washer between the shank and scooter bottom.
  5. Replace the shank, securing it to the scooter chassis by tightening the screw.
  6. Slide the square side of the bolt into the shank so the round side of the bolt points to the outside of the scooter.
  7. Slide the wheel onto the bolt.
  8. Using two Allen keys, insert one into the square side of the bolt and hold it steady. Insert the second Allen key into the round side of the bolt and rotate clockwise to tighten.

Left Shank for Mini

SKU: 1144

• Product Details

  The sturdy shank attaches the left front wheel to the chassis.  Compatible with Mini Micro and Maxi Deluxe only

Right Shank for Mini

SKU: 1145

• Product Details

  The sturdy shank attaches the right front wheel to the chassis. Compatible with Mini Micro and Maxi Deluxe only

Chassis for Mini

SKU: 1284

• Product Details

  Accidents happen, but fortunately, there’s an easy fix for a damaged frame. A new hard plastic spine will get your scooter rolling again.

  To install:

  1. Use a Phillips-head screwdriver to remove the eight black screws on the underside of the scooter.
  2. Remove the colored deck from the black frame, lifting up from the rear end of the scooter first.
  3. Remove brake screws (on silver square directly behind brake).
  4. Use Allen key to remove bolt from rear wheel, then remove wheel.
  5. Use Allen key to remove bolt from front wheels, then remove wheels.
  6. Use 9/32 or 7mm ratchet to remove steering link screw and washer in crossbar.
  7. Use Phillips-head screwdriver to remove small screws on reinforcement plate and larger screws on b-bend cover plate.
  8. Remove b-bend wires.
  9. Use Allen key to unfasten bolt in chassis and remove bolt and washer.

  Repeat steps 9-1 in reverse order to attach new chassis.

• Video

Steering Clip

SKU: 1141

• Product Details

  The steering clip installs easily into the bottom of the T-bar or pilot stick. Just look for the triangle-shaped stopper.

  To install:

  1. Remove the old steering clip from the bottom of the T-bar or pilot stick.
  2. Pinch the V-shaped part of the spring together to push in both sides.
  3. Insert the pointed end into the bottom of the T-bar, making sure to line up the triangle shaped stopper with the opening.

O-Bar
Handlebar Only

• Product Details

  O-bar (handlebar only) for Micro Mini, ideal for riders ages 2-3. Does not include Seat attachment or scooter.

  Top "O" of handlebar can be reached from 17-20 inches thanks to its circular shape; the material of the "O" portion is a soft and easy for little kids' hands to grip. If you need an O-bar with adjustable seat, please refer to the following product: https://microkickboard.com/products/mini-seat-o-bar

  We have found that this handlebar is preferable (over the taller T-bar) for kiddos standing between 20-30 inches tall.

Steering Crossbar for Mini & Maxi
Crossbar Only

SKU: 1147

• Product Details

  Steering Crossbar for Mini and Maxi (crossbar only) - Part #1147. Compatible with Mini and Maxi only

Set of Deck Screws
8 for Mini Deck

SKU: 1150

• Product Details

  Set of 8 Mini Deck Screws - part #1150. Used to affix Micro Mini Deck onto black frame. Compatible with Micro Mini Classic

Screws
2 & Spacer Plate for Mini & Maxi B-Bends

SKU: 1235

• Product Details

  Screws (x2) and Spacer Plate for Mini/Maxi b-bends - Part #1235 (b-bends not included). Compatible with Micro Mini Classic, Micro Mini 3in1, Micro Mini 2-Go, and Micro Maxi only (not compatible with Mini Sporty)

Instruction Manual Packet
Teen Adult

SKU: 105

• Product Details

  Misplace your instruction manual packet for your Mini or Maxi? We have you covered! Instruction Manual Packet (with x2 No. 4 Allen Keys) for Mini & Maxi - Part #105-Packet-Mini-Maxi

• Specs

  • Age Range :
    Teen Adult

B-Bend Plate for Mini & Maxi

SKU: 10402

• Product Details

Replacement Seat
Seat Only for Mini 3in1

SKU: 1417

• Product Details

  Replacement Seat (seat only) for Micro Mini 3in1. Connector hardware not included. Compatible with Micro Mini 3in1

Axle Mini Left - Circ Head

SKU: 4662-C

• Product Details

Spacer between bearings, 10.25mm - Mini & Maxi wheels

SKU: 1055

• Product Details