Parts: Handlebar Grips for Mini & Maxi

SKU: 1415

• Product Details

  This set of two rubber handle bar grips make it easy to update the T-grip portion of your scooter.

  To install:

  1. Use scissors to remove stock grips and any remaining rubber fragments.
  2. Pour water into new grips, then pour it out. This step temporarily lubricates grips.
  3. Slide wet grips onto T-bar, butting grip edges against the shaft of the T-bar. (Proper positioning is very important to keep grips from sliding off.)
  4. Allow grips to dry before riding.

Parts: 80mm Rear Wheel for Mini & Maxi

SKU: AC0021

• Product Details

  The long-lasting polyurethane wheel comes with the bearings and spacer already installed, making switching your wheels quick and easy. Order two if replacing both rear wheels. 80mm.

  To install:

  1. Use a socket wrench with No. 4 hex head attached along with a spare No. 4 hex key
  2. Hold the square side of the axle still using the No. 4 hex key; loosen circular side of axle using socket wrench
  3. Pop the wheel out, replace it with a new one, and reattach the screw.

• Video

Parts: Brake for Mini

SKU: 1687

• Product Details

  This tiny part works hard to keep riders safe in stop-and-go traffic. Check yours for wear periodically and replace when necessary. To install: Use a Phillips-head screwdriver to unfasten the eight black screws on the underside of the scooter. Remove the colored deck from the black frame, lifting up from the rear of the scooter first. Unfasten the two silver screws next to the brake, then remove the bolts and stock brake. Replace with new brake, reattaching bolts. Position the deck on the black base, rear end first, and replace the eight screws.

Parts: Brake for Maxi

SKU: 1851

• Product Details

  For the Maxi scooter, this tiny part works hard to keep riders safe in stop-and-go traffic. Check yours for wear periodically and replace when necessary. 

Parts: 120mm Clear Front Wheel for Mini & Sprite

SKU: AC5005B

• Product Details

  When pitted sidewalks and bumpy streets wear down wheels, it’s easy to replace them. Each wheel comes with bearings and spacer pre-installed. (Order two if replacing both front wheels.) 120mm.  Important note: Left wheel is reverse-threaded and is the opposite of righty-tighty! 

   

  To install:

  1. Use a 12mm wrench and a No. 4 hex key
  2. Hold back side of axle still using hex key; loosen outside of axle using 12mm wrench
  3. Pop the wheel out, replace it with a new one, and reattach the screw.

• Video

Parts: Bolt & Screw for Mini Rear Wheel & Shank

SKU: 1138

• Product Details

  Replacing the hardware on your rear wheel/front wheel is quick and easy. Comes complete with instructions. (Not compatible with Micro Maxi).

  To install:

  1. Using two Allen keys, insert one into the square side of the bolt and hold it steady. Insert the second Allen key into the round side of the bolt and rotate counterclockwise to loosen.
  2. Replace with new bolt and screw. Tighten down, holding the square side steady with one Allen key and rotating the other Allen key clockwise in the round side.

Parts: 120mm Black Front Wheel

SKU: AC5006B

• Product Details

  Each long-lasting black wheel comes with the bearings and spacer pre-installed to make it easy to upgrade your ride. For the Maxi Kickboard and Kickboard Compact.  Important note: Left wheel is reverse-threaded and is the opposite of righty-tighty! 
  

   

  To install:

  1. Use a 12mm wrench and a No. 4 hex key
  2. Hold back side of axle still using hex key; loosen outside of axle using 12mm wrench
  3. Pop the wheel out, replace it with a new one, and reattach the screw.

• Video

Parts: B-Bend Springs

SKU: 1227

• Product Details

  This set of two wire springs fit behind the two front wheels, helping your scooter maintain proper steering tension.

  To install:

  1. Look for the two screws on the bottom of the scooter, just behind the two front wheels. Remove the screws.
  2. Remove the rectangular black spacer.
  3. Use a flat head screwdriver to pry out the stock b-bend springs.
  4. Pull the wheels away from the b-bend, insert the spring into place, and press down with your thumb.
  5. Replace the black spacer and screws.

• Video

Parts: Handlebar Clamp for Mini Deluxe

SKU: 1813

• Product Details

  Handlebar Clamp for Mini Deluxe - Part #1813. Compatible with Mini Deluxe only

Parts: Black Handlebar Clamp
Complete

SKU: 1456

• Product Details

  Black handlebar clamp for Maxi Micro

Parts: Deck for Mini Original

SKU: 1337

• Product Details

  A brand new deck makes your whole scooter look like new, especially when you combine it with matching handlebar covers (sold separately).

  To install:

  1. Use a Phillips-head screwdriver to remove the eight black screws on the underside of the scooter.
  2. Remove the colored deck from the black frame, lifting up from the rear end of the scooter first.
  3. Position the new deck on the black frame, snapping the rear end on first.
  4. Replace the eight screws.

• Video

Parts: T-bar for Maxi Original
Children

SKU: 1352

• Product Details

  T-bar for Micro Maxi. Compatible with Micro Maxi only.

• Specs

  • Age Range :
    Children

Parts: Locking Button & Spring for Handlebar

SKU: 1023

• Product Details

  Handlebar Locking Button & Spring - button that "pops out" when handlebar is raised to tallest setting. Part #1023.

  Compatible with:

  Micro Maxi, Flex, Bullet, Sprite, Monster Bullet, Micro White, Micro Black, Flex Blue, Rocket, Speed+

Parts: Left Axle for Mini

SKU: 4662

• Product Details

  Left Axle for Mini

Parts: Steering Link
Bolt/Nut/Washer for Mini & Maxi

SKU: 1344

• Product Details

  Steering Link (bolt/nut/washer) for Micro Mini / Maxi - Part #1344. This part attaches one side of the steering crossbar. Compatible with Micro Mini and Micro Maxi only

Parts: 19mm Headstock Bolt & Screw for 2-Wheeled Scooters

SKU: 1031

• Product Details

  19mm Headstock Bolt & Screw for 2-wheeled scooters. Compatible with Micro Sprite, Flex, Rocket, Monster, and Micro Classic
  
  

Parts: 44mm Bolt & Screw for Maxi

SKU: 1228

• Product Details

  44mm Bolt and Screw for Micro Maxi - Part # 1228

Parts: Handlebar Locking Button & Spring

SKU: 1586

• Product Details

  Handlebar Locking Button & Spring - Part #1586. This is the button that "pops out" to secure the handle at tallest height setting. Compatible with Mini Deluxe and Mini 3in1 Deluxe only

Parts: T-bar for Mini Original
Children

SKU: 1140

• Product Details

  T-bar for Micro Mini Original. Compatible with Micro Mini Original, Micro Mini 2-Go, Micro Mini 3in1, and Micro Mini Sporty

• Specs

  • Age Range :
    Children

Parts: Right Axle for Mini

SKU: 4660

• Product Details

Parts: T-bar for Mini Scooter
Children

SKU: 1689

• Product Details

  Compatible with Mini, Mini 3in1, and Mini Original scooters.

  Please note, when purchasing to utilize on a Mini Original scooter, the colors may not match 100%, depending on when your scooter was purchased. 
  

• Specs

  • Age Range :
    Children